Sealed Lead - Acid Battery 6-GFMHR Series for Standby Power
Classification: knowledge
Release time: 2026-11-18
Summary:
Fengri supplies the Sealed lead - acid battery in the 6-GFMHR series. The range is described as a high power valve-regulated sealed lead-acid battery for standby applications. The models are rated at 12 volts and cover a C10 capacity from 80 to 250Ah, with a 15 minute constant power rating from 300 to 820W per block.
What Valve Regulated Means
A valve-regulated lead-acid battery is sealed during normal operation. The valve releases gas only if the internal pressure rises above a safe level, and the recombination design reduces water loss. That is why the battery is called maintenance free: the user does not top up the electrolyte.
The sealed design still needs a suitable installation. The battery room should be ventilated, the charger should be set for the battery type, and the terminals should be kept clean and tight. A sealed battery is not a license to install it in a closed, hot cabinet without checking the temperature rise.
The page lists the series as a high power design. High power cells are built for a short discharge at a high current, which suits a UPS, a switchgear closing operation or a telecom backup that must carry a load until the generator starts. The same block can also serve a longer, lower current duty, but the capacity and the end voltage should be checked for that use.
Models and Dimensions
The series includes the 6-GFMHR-300W at 12V and 80Ah, the 440W at 120Ah, the 550W at 150Ah, the 600W at 180Ah, the 700W at 200Ah, the 750W at 220Ah and the 820W at 250Ah. The 15 minute constant power follows the model number, from 300W to 820W.
The dimensions are listed for each model. The 300W block measures 306 by 168 by 214 millimeters, the 440W measures 406 by 170 by 240, the 550W and 600W measure 484 by 170 by 242, the 700W and 750W measure 520 by 238 by 234, and the 820W measures 521 by 268 by 227 millimeters. A battery room layout should use the actual dimensions and leave space for cables and service.
A string is built from several blocks. The number of blocks and the connection scheme decide the string voltage and the backup time. The buyer should send the load profile, the required backup time, the end voltage and the ambient temperature so the string can be sized. A block that is correct for one load may be too small for a longer backup.
Charging and Maintenance
For the Sealed lead - acid battery, use a charger with a float voltage and a temperature compensation curve that match the battery. A float voltage that is too high shortens life, and one that is too low leaves the battery undercharged. Check the charger settings after installation and record the float current at the commissioning stage.

Inspect the string at regular intervals. Look for loose terminals, swollen cases, cracked covers and electrolyte leakage. Measure the string voltage and the individual block voltages, and compare them with the commissioning record. A block that drifts away from the rest is a warning sign.
Temperature has a strong effect on life. A battery installed in a hot room will age faster than one in a controlled room. Keep the battery away from heat sources and direct sun, and check the ventilation in the room. For a long backup requirement, the battery bank should be sized with the expected end-of-life capacity in mind.
At end of life, the battery should go to a lead-acid recycling route. Do not open the case, do not mix the battery with general waste and do not store a damaged battery indoors. A sealed battery still contains lead and electrolyte, and the local rules for transport and recycling apply.
Ordering and Support
Fengri lists lead-acid, lithium, sodium, DC power supply, UPS and energy storage products. A project that needs a complete standby power system can discuss the battery, the charger and the DC distribution in one review. The company is based in Liuyang, Hunan.
To request a quotation, send the model, the string voltage, the backup time, the load profile, the ambient temperature and the destination. State whether the project is for UPS, telecom, switchgear or another standby duty. Our team will confirm the Sealed lead - acid battery configuration and the terminal type.
For product questions, contact fengri@fengri.com or call +86-731-83219796. The product page also lists fengridianqi@126.com as a contact address. Our team can provide the datasheet and the dimensions for the model you select.
If you are comparing batteries, ask for the 15 minute power, the C10 capacity and the dimensions on the same basis. A block that is smaller but has a similar power rating may not have the same backup time, and the string design should be checked as a whole.
Key words: Sealed Lead - Acid Battery 6-GFMHR Series for Standby Power
Liuyang - Hunan - China
+86-731-83219796
fengri@fengri.com
